Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
I use 51822 nrf6130 "device_firmware_updates" example to update AP. When I build "dfu_dual_bank",the update will success. But when I use "dfu_single_bank",the update will...
Hi,
Do the nrf_temp functions, nrf_temp_init() and nrf_temp_read() only work for the nrf6310 board? Are there equivalent functions for the EK?
Thanks,
Mike
I have been trying to connect a nrf8001 device to a Android 4.3 device and it is discovered ok but fails when it tries to do a service discovery. After some deep digging I...
I am having the same basic issue that is described here:
https://devzone.nordicsemi.com/index.php/setting-advertisement-parameter-s-for-custom-profile
Including the error...
hi,
first of all i need to say, i am very happy to found the s120 softdevice where we can implement the client role also
i downloaded new alpha version of s120 softdevice...
hello,
i am using s120 softdevice along with nrf6310 mother board, the problem is i am dumping the code into the device, but i am having doubt how to verify that it is...
Hi, I am creating a PCB design and am not sure if I should connect the pad under the nRF24L01+ to the ground plane with a couple of vias.
The data sheet says it should...
Is there a plan to support the BLE central role in the software stack?
As it is now, I absolutely cannot use the nRF51822 since the S110 stack does not support operating...
The attached test program and logic analyzer displays shows that the function twi_master_transfer() returns to the calling program before the transfer is complete, if TWI_hw_master...
The error I get is app_error_handler 0xDEADBEEF, 360 (line number), src\ll_lm.s0.c
This is with SD 5.2.1
With SD 6.0.0.1-alpha, sometimes I get
app_error_handler...
Does anybody know of any plans to combine the Peripheral and Central roles into a single SoftDevice?
The killer application that this provides is the ability to create...
