Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
The 9161 has 256 KB of RAM, but while building the application, it reports that only 32 KB is available for the application. If I create some large static buffers (e.g. 40...
I've tried the following with the Quick Start app v1.2.0, v1.1.0 and v1.0.1. The log below is from v1.1.0, if I recall correctly. All logs are about same. Programmed the Asset...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
Hi,
I am currently working on the Matter ecosystem for an IoT home automation product. I have referred to the Nordic technical documentation on the Matter Bridge, available...
hello everyone,
I built an application based on the peripheral_uart sample running on the EV-BM833 board. The application includes the Nordic UART service.
Using the nRF...
I am in the process of migrating to NCS 2.7. My project includes NSIB, MCUBoot, TFM, and the application. Everything works fine with multi-image builds.
However when using...
I am working on an nRF52-based BLE peripheral (beacon) using the Nordic SDK. I want to implement functionality where the advertising interval can be updated dynamically from...
Hi Support Team
We want to develop an application of combining a PDM microphone and a nRF54L15. When we speak a word into the microphone, the nRF54L15 will perform a corresponding...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello,
I've tried to compile the experimental_ble_app_hrs_pairing_nfc example using Keil uVision. The example requires the NordicSemiconductor::nRF_DeviceFamilyPack version...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
