Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi All,
I am trying to implement I2C Slave functionality on NRF52832, So NRF52832 will act as a I2C slave.
So i found there is an example TWIS Slave and TWI Master Mode...
Hello,
I'm using nRF52840. I developed a project using openthread libraries: in particular I included " libopenthread-nrf52840-softdevice-sdk.a " library to have the CLI...
Hello. I'm using the NUS BLE service to send ADC sensor data. I am having the SAADC callback function call ble_nus_data_send() to send raw samples. I have set the min and...
I need to measure full power consumption of nrf52, on PCA10040 from... a 5V source (because including some other 5V devices). I measure it from 5V pin and not usb plug. I...
Hi,
as I know from the mesh spec, the number of elements cannot change after a device was provisioned. Nordic even went so far as to define the number of elements during...
Hi, how to measure RSSI in OpenThread? I have 2 nodes, what is correct state that I have to assign to each node to do transmit/receive test, is it leader and router? or router...
Hello,
We're thinking of powering external sensors through GPIO pins configured as high-drive. The sensors themselves consume only a few milliamps at most, which is easily...
Hi,
I would like to control a piezo driver using GPIO pin on nRF52840 DK.
I've read posts about this kind of application. But still confused about how to set up PWM...
Hello again Nordic Pro's,
I have a mildly modiffied version of ble_app_uart_c that compiles and runs fine on an NRF52-DK board. I am now trying to use the same code on a...
Hi,
I'm very new to the Nordic BLE chips. Sorry in advance for asking stupid questions, but I'm willing to learn! This is my first project for my current job, I want to...
Hello,
I've been trying to run the OpenThread mqttsn_client_publisher example from the SDK. I have also set up the border router according to the tutorial on the infocenter...
Hi:
I meet a strange softdevice assert when I do dfu in nrf52832. There is no info or call stack for this assert, I only get the assert is NRF_FAULT_ID_SD_ASSERT.
Do you...
Hi,
I have been working with the Thingy:91 at the version 1.2.99 but this also happens on previous versions (I do not know which it was but the serial_lte_modem code had...
Hello,
I am facing a issue with the LN service. I am notifying the position at 10Hz and this work well. I have implemented a custom service that allows to send a file by...
Hi,
Just as the title says, I want to use nRF52840 as a peripheral(s140, v7.0.1, BLE_NUS_MAX_DATA_LEN is 244) and using NUS.
And it may pair to a nRF51822(s120, BLE_NUS_MAX_DATA_LEN...
