Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hello,
I am working on a school project with my team that requires one master device and up to 30 slave devices which will be controlling LEDs. I was thinking the nRF52840...
When enabling BLE on nrf52840, we are using specific API to access flash erase and write commands. All is working fine 99% of the time in term of read / write / erase into...
Hi Sir We are scanning nearest BLE using NRF Scanner example using 1- NRF52840-DK and 2. BT840 . We are getting good RSSI value using 1 but very poor RSSI values when we are...
Hi,
I am using nrf52832 with s132 softdevice and SDK17. I want to disable bonding and pairing in ble_multirole code. I have tried disabling the SEC_PARAMS_MITM, SEC_PARAMS_IO_CAPABILITIES...
Dear Sir,
I am using SPIM , EasyDMA array list,with following flags
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER , NRF_DRV_SPI_FLAG_RX_POSTINC , NRF_DRV_SPI_FLAG_HOLD_XFER&
...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
i'm building an amplifier that can play sound over bluetooth. I intend to use the nrf52832 to send i2s data to my dsp chip. based on the loopback example, i have an idea on...
Hello,
I was reading through the code of the asset tracker application and noticed that there is no while(1)/for(;;)-loop. I see this for the first time in a board application...
hello,
we are in process migrating to SDK 16.0 and service pack 8.27 or higher. While performing an upgrade we encourage few problems and would like you expert advise...
2 Questions, both short:
1. Documentation error in Softdevice 15.x and 14.x header files:
/** @note If any of the discovered services have 128-bit UUIDs which are not...
"AT+CEREG=2" "AT+CFUN=1"
Getting the correct responses of above mentioned AT commands.
But after that, when any command is send on LTE Socket, " at_host_at_socket_write...
Hi,
I was randomly inspecting Bluetooth devices around in nRF Connect and I found out that many Apple devices advertise with TX Power Level 12 or 24 dBm. From my understanding...
Dear Nordic Team,
I'd like to inquiry how I am supposed to send a UTF8 string as the value of a characteristic.
I am trying to implement the FTMS service and the part...
Hi !
I want to connect 2 of my units to each other via BLE5 long range coded phy (125Kb).
I also want to be able to connect an android / ios phones to each unit simultaneity...
