Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm trying to play some sounds on a piezo with the help of the pwm. I tried to set the period with pwm_set_dt but only the first call is successful and every subsequent...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We would like to know, whether the nRF5340 supports any camera interface. If it support...
I am currently trying to get LLEXTs to work on the nRF5340 Audio DK. I was able to compile an llext and load it successfully, using the cmake features, However, I would like...
Hi, I would like to consult how could I deal with this error and build the code succesfully.
In device.h
'__device_dts_ord_113' undeclared here (not in a function); did...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
The Matter stack’s auto-generated file ` access_buildconfig.h` explicitly sets ` CHIP_CONFIG_USE_ACCESS_RESTRICTIONS` to ` 0` , overriding my attempts to enable it. This prevents...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
How do I preprocess a C file (typically done by passing the "-E" option to the compiler) in VS Code with nRF Connect SDK 3.0.0 or later? I want to see how a complex macro...
I built the littlefs zephyr example found in "/zephyr/samples/subsys/fs/littlefs"and then modified it to use the external flash "MX25R64" by adding an app.overlay file. I...
