Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello
Currently I use the example "ble_thread_dyn_mtd_coap_cli_pca10056" and I would like that my application can detect timeout of the messages sent on the Thread network...
Hello, First of all, I hope you are doing okay about the corona virus crisis. I wish that you stay healthy and safe . Recently, I have been trying to configure ble_app_uart...
Hi Sir,
In the datasheet (V1.1), the table-145 shows the dimensions of WLCSP, but there is no tolerance of D/E/D2/E2
Could you help to advice what is the tolerance of...
I have a project where I am implementing an alternative logging backend. My design is modular so there could be multiple logging backends. Each backend is initialized with...
UPDATES after original posting:
I now remember having the same problem described below, once before on my windows installation. At that time I decided to switch and reinstall...
I'm working with the nRF5 SDK v15.3 and a nRF52840 Dongle; developing on Keil uVision V5.29; Compiler: Armcc V5.06
While debugging I that in my programm a NULL pointer was...
HI ! I found an error in the source code because of which the db discovery event handler on DIS client does not work, namely: in the function ble_dis_c_on_db_disc_evt () ...
Does it cause issues if the application was built with a different SDK level than the bootloader? I have a project I'm adding a bootloader to, and it isn't working. I have...
SDK 16, 52810
my board has done the change as the 52810 spec says about dcdc part. Now I wonder HOW do I enable it in my code. Somewhere it says to call sd_power_dcdc_mode_set...
I want to measure the current during sleep,so I write my code as follow:
I queried the manual data that the current is 1.5uA, but 14.0uA is my measuring result. So what...
I am testing the serial interface to BLE messaging using "Bluetooth Mesh Packet Send Opcode: 0xab" - it's working very well. However I have found one thing that is puzzling...
Hello there,
I am working on secure dfu. I followed all the steps mentioned in this post and successfully created the secure .zip file.
Here's what I did(In this order...
First time I programmed the BMD 300 IC ,it got programmed and worked good.After some days later I tried program the board, But the previous code was present in the mcu, i...
