Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I have the driver setup like all of the other sensor drivers I'm using, but I can't seem to find a device tree or Kconfig
This should be enabled by the CONFIG_SOC_NRF52840_QIAA...
Hello!
We have a custom board connected to a battery and a USB cable
Our fw calls:
NRF_POWER -> SYSTEMOFF = 1 ;
The board turns off.
And then we remove the USB...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
Hello
I am starting with nRF 9160 DK and Segger Embedded Studio, I installed Segger through toolchain, the activation sim, updated of certificated and connect the DK to...
Hi everyone
Currently, I am working on a project related to the mesh network friendship feature on nrf52840. I am having the following problem: I have established a friendship...
I tried to debug UART communication between 52840 development board and 9160 development board. I sent 9 bytes of data from 52840 side, but I only received 8 bytes of data...
Hi,
I can't find how to get data received by interruption of UART. I've used libuarte example and I tried to get data from buffer buf in uart_event_handler, but it doesn...
I can see that other people have run into the "no code for breakpoint" problem when attempting to use the SEGGER debugger. I have read the earlier posts. I have not been able...
Dear Sir/Madam,
Can you please help to check and advise if both part# nRF52840-Dongle and nRF52840-DK have KC certificate? Thanks.
Best Regards,
Dan Lee
Hi,
I'm using for awhile TIMER0 and I want him completely disable.
I'm setting a TASKS STOP to stop a timer, clearing a interrupt and disabling interrupt in NVIC, but...
I'm looking at the datasheet for the NRF52832 because I'll be using it with a Raytac module and I'd like to know for sure how the SPI pins are set.
I see in the datasheet...
