I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Dear Members,
How can I connect via ANT+ to Garmin GSC10 ?
then display cadence and speed value in UART ?
Is it related with this function in ant_bsc_rx_d52_s212.uvprojx...
Hi
My problem is very simple but I don´t know how fix it.
I have a project in my work and it goes very well, but when I returned home,I have build It and it goes with...
Hello,
I'm having an issue with my nrf52832 with and ICM20948 IMU attached. My issue is related to wake up on motion. I believe I've set it right but I can't make it work...
Hi.
I have several issues when trying to respond to Direct Methods (using v1.4.0 of the SDK):
In azure_iot_hub.c:
evt.data.method.rid = atoi(topic->prop_bag[0].value...
Hi !
I am working with a NRF52832 and with SDK 15.2.
For my application, I need sometimes to deactivate the Softdevice to begin some radio tests.
So I have programmed...
I am doing the procedure described in the nRF52840 specification, figure 193 "UARTE reception with forced stop via STOPRX".
I am using 1Mbps with hardware flow control....
I'm testing out the Thingy91 Asset Tracking Application, but I notice when I poll the Accelerometer, I only get junk data back. +/-20m/s^2 on all axis. I'd test this application...
Hi! This is the first time that I develop a BLE system with this MCU, I want to know if it is necessary to install so many vias making a shield around the entire pcb. If so...
Hi,
i'm using SDK11 with NRF52832
After a pin falls from HIGH to LOW The GPIOTE_IRQHandler calls a function in my program to read 8 bits from the bus (Inside the interrupt...
Following the seminar today I tried to build and run this example.
built on command line using west (non-secure nrf9160-DK target)
in a continuous loop I get
```
SPM...
I want to dump lengthy log data out through an RTT connection if the JLink is connected but NOT spend that time if there's no physical RTT channel present. The idea is that...
1.Customers need to use nrf52833 for design and production in this package: WLCSP package, 3.175 x 3.175 mm
2.I noticed the description in this manual:nAN-38 WLCSP Handling...
At present, the SMS is sent normally. The format of nrf9160 is 7bit, and can send a maximum of 160 characters. However, how to send it in packages if the content exceeds 160...
We are looking for a Bluetooth 5.1 indoor positioning solution at precision around 1m.
Could you help figure out which platform/reference design is capable of implementing...
