I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
I am working with the nRF52840 DK and was looking for a way to set a compare register to trigger at 300 ticks, and another to trigger at 40000 ticks. The register that triggers...
Hi,
I am a new comer so perhaps I made a mistake during project configuration.
I am using nrf Connect v3.4.2 on Windows.
I trie to add CC310 libray in sample hello_world...
The detected device could not be recognized as neither JLink nor BLE could be captured in wireshark, nor could the nRF Connect v3.4.2 - Programmer produce "Unsupported device...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both BLE scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi. This is my first experience using Nordic Products and I have run into some issues trying to "Open nRF Connect Studio Project" from SEGGER Embedded Studio. I want to run...
Hi
I'm trying to load the sample project Mesh light using SDK 1.3.0 but cannot load the configuration file properly. Im using a nrf52840DK
I have tried to update requirements...
Hello,
I wanna create a central/peripheral device. This device must be connected to mobile phone as peripheral. Also, it must be scan peripheral device's advertisement and...
In order to implement the event callback mechanism, the Observer Pattern is implemented by "Flash Section". This idea is novel, But what are the advantages of this method...
Hi everyone,
I try to write using I2C but I fail and I cannot figure out the issue
This is my code snippet.
When I run it it returns the following error
It fails...
Hi everyone,
I am looking the TWI examples and I am confused regarding the nrf_drv_twi_tx and nrf_drv_twi_rx . What I've understand so far is that the nrf_drv_twi_tx function...
Hi,
We are developing the project based on nRF52840 chipset. We are configuring the chip for mesh application and using generic on/off model to send the data on the mesh...
Hello ,
There is two kind of clock source as i can see from the sdk files;
one of them is cpu that is ok but for the first one i couldn't figure out it's source "NRF_SYSTICK_CSR_CLKSOURCE_REF...
