Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
I am using zigbee light_control examples in nRF5_SDK_for_Thread_and_Zigbee_v4.0.0 for my zigbee projection.I want to know how the zigbee network build and which command will...
Hello, I have been using segger embedded studio v4.16 for almost one year using free license. today it says my evaluation period is expired. But they say it is for unlimited...
I have a setup with one transmitter and three receivers. The transmitter (nRF24L01+) sends a message to the receivers (nRF52832, using SDK v15.3.0) every 10 seconds. The receivers...
Setup: Segger Embedded Studio v3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 Custom Board
Hello,
I based my code off of your Zigbee cli_agent_router example. In the...
We use both the iOS and Android DFU library to support DFU through our mobile application. Recently we found that Samsung phones running on Android 10 have a problem with...
Hi,
I'm developping some test suite for one of our ble products in development, and I'm encountering some unexpected behavior using pc-ble-driver-py.
The test I perfom...
Hi, this is probably an easy one. Starting with the ble_app_uart peripheral example, I am customizing an application. I observe that two events with IDs 58 and 85 come through...
I have setup a timer interrupt whivh fires at about 10 seconds which I can follow on an RTT viewer the ISR demands two ADC's to convert the voltage levels on their pins, I...
Hi Team,
When we add RNG peripheral Driver related code changes to our custom project we are getting linking errors, but when we compile individual files it is compiling...
Summary
I am using UARTE on NRF52840 at 115,200 but am experiencing "bit loss", i.e. the UARTE is losing a few bits in the incoming stream causing corruption of all incoming...
Hi,
I’m new to this dev environment and hoping I may get some help.
I’m building my backup application binary and want to store it in the upper ½ of flash on my nRF52840...
I am attempting to us the nrf52840 but am unable to interact with any of the GPIO pins on the P1 register. anything on the P0 register works just fine. I have attempted setting...
I am trying to set up the nRF51822 Adafruit Bluefruit LE Sniffer. I first go to this link https://learn.adafruit.com/introducing-the-adafruit-bluefruit-le-sniffer/v2-wireshark...
