Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
Hi,
After doing an sd_nvic_SystemReset(), the bootloader does start advertising, but for some reason the android app nRF Master Control cannot connect to it.
If I connect...
Hi everybody,
I'm currently writing an Android application allowing me to communicate with a NRF51422.
I've created on the Nordic chip one proprietary service with 2...
please help to confirm the ESD grade of nordic SOC. i can't find all the parameters(HBM, CDM,MM) in the datasheet, only HBM in 24LE1, and only HBM&CDM in nRF51822.
I'm trying the ble_app_hrs example on a custom nRF51822 board with s110 6.0.0 softdevice.
Debugging in Keil, the firmware runs fine up to ble_stack_init(). Within ble_stack_init...
Hi All!
In all exsamples in function "ble_evt_dispatch" we have different order to call sub functions.
Most functions to call is:
dm_ble_evt_handler (device manager...
I'm testing a data collecting program which samples data every 2s and reports it through UART ( printf("data=%d\r\n", data) ) on a PCA10001 board. I found this program may...
Hello,
Got a question about nRF51422 and S310 stack. I am trying to understand how the radio is being handled and how the softdevice handles events in a specific case....
I tried communication between PC and my own board(nRF51822) PCA10000 usb dongle&MCP, I found that the first time I send n(where n is any decimal number) bytes data(s) from...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
static conn_mw_handler_t conn_mw_handler_get (uint8_t opcode)
Inside the function,
for (i = 0; i <conn_mw_item_len; i ++)
{
if (opcode == conn_mw_item [i] .opcode...
