Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I am searching for a clean way to handle a timeout (because I2c device does not respond or there is a hw issue with the I2c bus).
On startup I probe different I2c...
Hello ,
I am interfacing the customized board nrf52832 , As of now we didn't populated the 32 MHz externally . so I am trying to program the peripheral alone. Twi sensor...
Greetings,
We developed a customized board using NRF52832. We flashed the code using NRF connect JTAG. The LED is working fine. But when we flashed the BLE_UART BLE is not...
Fired up nRF Connect v3.6.0 on MacOS
Plugged in new 9160-dk and switched on.
Connected to USB.
Selected board. Green dot appeared but nothing in the "Device memory layout...
Good morning,
We have developed a prototype based on the nRF52840. We have also developed an Android application.
When smartphone has device already bonded the application...
Hi,
I am a beginner in BLE Mesh. I am trying to create a Mesh network for residential purpose using Tuneable lights, switch and sensors.
Mesh SDK version : 4.2
On the...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see below API for initializing/updating advertising data.
I want to know what does it do with the buffer...
Hello
I am now quite familiar with the basic PWM playback capabilities of nRF52832. However, I would like to make a chain of simple and complex PWM playbacks.
I have already...
Hello,
I am developing an application that sends data from an Arduino Nano 33 BLE Sense to a custom Android app (Motorola Edge running Android 10). The Arduino board is...
Hi,
As many of you, I'm tryng to compile pc-ble-driver (v4.1.2) found in https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.2 , just to see how the code works...
Our application stores sensor data in flash and sends the data on request via USB. But if the device is connected to Bluetooth once then it is having issues in USB data transfer...
Hello,
At this point I have been able to successfully customize and run the mcuboot procect.. Mcuboot is successfully built and linked with my app.
However I am would...
Hello
I'm Strangistra and I work on a Adafruit Feather nrf52832.
I have the Arduino IDE 1.8.13 and I use the FastLed library 3.3.3.
I have a strange behavior with the...
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.1.0/nrf/samples/bluetooth/peripheral_lbs/README.html
I'm talking about the above. SW5 switched to nRF52. However...
