Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
SAADC resolution is set to 8 bits, channel is configured as single ended. Is it correct to say that SAADC digital output should be between 0x0000 and 0x00FF(full scale)? ...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
Hi ,
I need to store strings in flash and came across the NVS. I referred to the example in samples/subsys/nvs and was able to do the nvs operation.
The following are...
Hey, so I was under the belief that the maximum size of data one can include in a BLE packet is 20 bytes (23 bytes total, 3 bytes overhead, so 20 total for custom data). With...
Hello! I have been working on bluetooth for some time and I just worked with connectable advertising until now. This time I am trying to add a beacon functionality too. The...
Hello,
I am developing a BLE and IEEE 802.1.4 multiprotocol device. I implemented a parser to change some settings of the device. T he configuration is updated with this...
Hi,
I'm trying to implement a SPI Communication between Arduino UNO and PCA10056 DK. PCA10056 DK run as a SPI slave.. Arduino uno run as a SPI Master.
The problem is...
I'm using SDK 15.3.0 and SoftDevice 6.1.1 running on an nRF52832.
The iOS application works correctly when it is running in the foreground. It is able to connect and bond...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
