Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi! I'm trying to understand the possibility of doing a FW update to an empty NRF52810 chip via a host MCU running Linux. We have this setup on a custom PCB, whereas the host...
Hello,
I have two quick questions about the nRF24L01+ chip that I wasn't able to find from reading its datasheet.
1. Is the chip pre-programmed by Nordic or does it need...
Hi,
What does the AT%XOPERID command do exactly? Does it just return the operator, or does it change settings too, such as bands, system mode, psm, edrx etc?
Kind regards...
nRF SDK: 16.0, Device: nRF52840, module: BTX480XE, softdevice: ANT_s340_nrf52840_6.1.1.hex
The setup:
BLE and ANT running on same device concurrently. The device is modified...
Hi,
I am new to OTA, wanted to explore OTA. Is there any available example code for OTA in the sdk 17.0 or mesh sdk and how to verify it. How to proceed with this?
Thanks...
Dear Community,
I have been testing eDRX on nRF9160. For that, I have modified nRF Connect SDK "udp" sample. I have set eDRX cycle to 20.48s. My program does the following...
Dear all,
I am trying to run the MSC example in order to learn how to develop an application with MSC capabilities in the future. I have already run the example in its default...
Hi,
I want to explore NFC for nrf52832, how shall i proceed so that i can able to read and write using nfc. I want to write from an external device to NFC and so that...
Direction finding is a new feature in BLE eco system. We can think of many applications for this technology. One well known is asset tracker. We can locate the coordiantes...
Our new prototype uses an ISP1807 (nrf52840 module). The schematic is almost the same as a previous working prototype based on the Ublox Nina B302. (also nrf52840)
I've...
Thanks in advanced. The platform is nrf52832 and sdk17.0.2. I want to use phone to update static key of peripheral ble device, is there an example for this?
This problem is very strange.
First,I install the software(nrfgo studio,nrfgo studio-win64-1212installer.msi) on the company computer,the colour of nRF5x Programming is...
Our peripheral application sends an L2CAP Connection Parameters Update Request to change the connection interval 30 seconds after connecting. For most hosts, it works fine...
