hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
We are working on our new product which needs a BLE connection with a mobile phone.
Our requirements are as follow:
1) Four digital output. (It's preferred to be...
Hello,
From the ble_app_uart example I created a version where instead of the UART the incoming data over BLE is processed using the scheduler.
Processing is not much...
Hi, i develop a bluetooth project with nrf52832 anad i am unexperinced about this topic. I searched for 2.4 GHZ antenna desgin bu can't found. There is a few topics about...
HW: nrf52833-DK
SW: SDK v16.0.0 and SoftDevice s140
We are using nRF52833 BLE direction feature and read IQ samples produced by BLE Radio.
The format of the IQ samples...
I am working on porting a project from the old sdk to the nrf5340 and the nrf connect sdk documentation seems to be incorrect and i am having major issues even getting this...
SoC: nRF52810
SDK: 17
Hello,
I want to confirm whether BLE_DFU_ENABLED is used or not.
InfoCenter ( https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/group__ble__dfu__config...
Hi,
I use the app "asset-tracker", and i would like to configure an external uart to connect a sensor to the board.
I modifed the code but i can't detect any new COM from...
Hi,
I am using nrf51422 and s130 softdevice for multirole. Is there any way to reduce the receiver power during scanning so that the overall current gets reduced?
Hi,
I'm trying to implement remote provisioning on an altered version of the light switch example in the SDK for Mesh v3.2, on nRF52832 development kits. The code I'm using...
I am using nrf52832, i want to send the sensor data continuously via ibeacon.
but while uisng sd_ble_gap_adv_set_configure() function return error NRF_ERROR_INVALID_STATE...
Hello,
I am testing a light switch system where each switch is capable of controlling multiple bulbs via multiple groups stored on the switch. I have noticed in the example...
As of what I've read in [1], nRF9160 uses ARM Cortex-M33. I'm not sure which qemu of the Zephyr OS is compatible with ARM Cortex-M33 the most ? qemu_cortex_m3 or none of them...
Problem:
I am trying to measure two voltages from the SAADC. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . It is using one SAADC...
Hi Nordic,
I am now using NordicDFU swift package for my iOS app. Before I was using an older version which was working perfect.
Now after I have updated the swift package...
