hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello. I have a issue about fstorage.
first, I using S332 SD and SDK 15.3.0 version and 52832.
Init flow is below:
Log enable -> SD enable -> SD BLE & ANT enable ->...
Hi,
SES is not including the extra cmake build options, i tried prefixing "--" as we do it in west build, note that it works west build "west build -b nrf9160_pca10090ns...
I am attempting to create a custom Buttonless DFU application by building on top of the default example from the SDK. Specifically, I am merging the Buttonless DFU app with...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
According to the Zephyr documentation here the way to implement an application-specific exception handler is to define k_sys_fatal_error_handler. When I try to do this I get...
Hi. I'm doing the firmware on the custom board.
This board turns on when the button is pressed through the power button circuit. And I created the reset function using NVIC_SystemReset...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
Hi, all
I'm using nrf52832 pca10040, s132..
I want to send and receive data over Tx , Rx pin.. with my custom board, cm1106 model..
<<<<<< I've connected the two devices...
Not something which I have experienced, but rather inferred from reading the code of nRF5_SDK_17.0.2_d674dde/nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend...
HI, I'm creating an IoT system, and planning to use THREAD to communicate between devices. Each device is running on a raspberry pi but I plan to use nRF52840DKs to do all...
Hi,
I am seeing a bricked device due to the fds_init() returning FDS_ERR_NO_PAGES. After some debugging, I found that all pages are marked as FDS_PAGE_DATA (no FDS_PAGE_SWAP...
Hello everybody
I hit another issue with sd_ble_gap_disconnect.
The short story is this one. I want the peripheral to initiate a disconnect if no activity for a predefined...
Hi, I'm working on an application (Zephyr) that uses nvs storage and it's been working just great for awhile (months) without any major issues. Today I noticed that when reading...
