hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
Hello,
I want to use BLE direction finding. In the product brief ( https://www.nordicsemi.com/-/media/Software-and-other-downloads/Product-Briefs/nRF52833-DK-PB-10.pdf?la...
Hi,
I need some help to interpret the LTE timers values that my network operator applies.
During network registration I requested RPTAU : 10 min and AT : 0 min, by issuing...
I want to connect the nordic ZigBee with Digi's XBee module.
I have configured the Digi XBee pro s2c module as coordinator and nordic as a router but they are not communicating...
Continuing the discussion that was documented here:
https://devzone.nordicsemi.com/f/nordic-q-a/64691/how-to-use-the-latest-version-of-californium
1) I modified the resources...
Dear Nordic Support Team,
I haven't seen any forum posts directly applicable to the issue I'm seeing so I hope you can point me in the right direction.
The basic Thread...
I wanted to try to test some of the nrfx_saadc v2 features in a project I'm developing. I downloaded and ran a couple of the examples from GitHub and they run fine on a nRF52...
Hi,
we are facing the following error. We bond our device (peripheral S140, SDK 15.3) with the following settings with iOS devices:
#define SEC_PARAM_BOND 1 // Perform...
Hi,
I am unable to build code. My Mac has just been updated to Catalina, not sure if that's caused the issue.
I am trying to build the standard "blinky" code but am getting...
Hello
I'm working on SDK v17. Receives certain data from the app, and LED timers work according to the data received.
The code that receives data from the app and parts...
Hello
I'm working on sdk v17. I want the LED to be printed out like a wave when I receive certain data from the app. (5 Times)
It is simple to use 'delay' and 'for' as...
I had my first encounter with Nordic chips a couple of years ago. To evaluate the devices, I used an nRF52832 to implement a small helper project. I was very impressed: it...
Hi Team, Is it possible to use the BLE NRF52832 module for audio applications like attending phone calls, listening music etc. If it is not possible with this module could...
