I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic:
It seems that mesh LPN can receive secure beacon via friend node, and if has no friend, LPN also can receive secure beacon if MESH_FEATURE_LPN_ACT_AS_REGULAR_NODE_OUT_OF_FRIENDSHIP...
I'm running some power tests on the nRF52 DK and, after fiddling with some of the power settings, I'm managing to get an idle current of about 1.8uA on the coin cell, and...
I'm sorry to ask a question that I'm sure has been answered before, but I can't find another post similar enough to be of help. I have an HID application that bounces back...
Dear All,
We are currently developing a low power application for the nRF9160, with ncs zephyr version 1.2.0. For our application we want to trigger an interrupt on both...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
Hi,
I would like to get some information about the reset's reason of my nrf9160 like
- The reason is due of an assert type "xxx"
- Where is the stack pointer
- .....
Hello,
I'm developing a BLE device and it consist of nRF52833 and a external UART component.
ble_app_uart example in SDK v17.0.0 is replaced app_uart to libuarte. The...
Hi,
I would like to know if we can enable codded phy while using mutli peripheral in conjunction with mutli central. Also peripheral should be scannable and connectable...
When creating dfu package using nrfutil, an error is displayed.
When I looked for and checked the file where the error occurred, a problem occurred in Python's max...
I am trying to run nrf52840 chip without debugger.
I want to run peripheral_uart example just to show advertising of bluetooth.
And when I use west debug --runner=jlink...
Hi,
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Then I flashed the agps code because just want to send GPS coordinates on the...
I am having issues using port pin 1.00 on the 52840 as GPIO. It will just not toggle.
I can successfully use most other pins, even those on the higher port. For example...
Hi
I have 2 identical PCB just out of production - same FW - one is drawing higher current (about 600uA).
The issue is found in mass production and about 1% is having...
I'm using nRF52 DK to send SAADC data to mobile app "nRF Connect" over BLE.
I'm using this code to send the data, but the mobile app "nRF Connect" can only show integer...
