Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
We are using nRF52840 chipset with SDK 15.0.0 with Mesh implemetation.
1. We are provisioning the mesh node using the nRF mesh APP.
2. Then we are resetting the...
Hello,
I had been looking at BLE mesh documentation as well as the examples on the SDK and looks every node should have a dedicated function. generic on/off server controlling...
Hello!
I am trying to interface with some old hardware that communicates over a single data pin. I need to take in varying 32-bit packets and output the data that translates...
Hi all,
The chip we used is nRf52832, the version of SDK I used is nRF5_SDK_15.2.0_9412b96.
The problem is when I pair to windows 10, sometimes PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
Hi,
I am using i2c driver available with zephr as i2c master. This is working fine.
I want to change the pins to P0.02 for SCL and P0.03 for SDA. I see multiple questions...
Hello,
I am looking into the peer manager and the LESC module and have some question regarding what is possible to do with this.
Is it possible to manage the private...
Hi,
I am updating SDK version from 15.0 to 17. We are using nrf52840.
I would like to know if these are necessary to add, as they were added in some examples, and if so...
Hi,
i have a problem when using the ble_uart connected to Raspberry-pie withe Bluez.
after 40 seconds the connection is lost.
tried to use several examples, but most...
Hello Community I am starter in nrf51822 i want to know if anybody has code for interfacing with ADS1115 since i didn't got any of the post which would be helpful, please...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
I want to measure voltages at all 8 channels but when I am enabling all channels its sending the values once only and after that its not sending anything, my requirement is...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
