When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Good Afternoon:
We are developing a BLE remote button using Nordic's nrf52840. We have purchased several devkits and are in the process of fabricating our own design specific...
Dear,
Im trying to use the motion to activate the GPS and deactivate GPS:
1. when it moves, GPS will be activated: Position-ON
2. when it stops, GPS will be activated...
I'm working on an nRF52832 based IOT product using Segger Embedded Studio for ARM v4.50 on my Windows 10 machine. My project uses FreeRTOS. Looking at the release notes for...
Hello,
This may be normal behavior once correct connection management code is in place, but I want to verify since originally I was looking at 2-3 minute connection times...
I want to use a comparator without interrupt.
The measurement is not time critical.
Therefore, I chose the LPCOMP.
For initialization I use the following code:
For...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
Hi,
I am working on a hub based on a raspberry compute module. Zigbee support is enabled by a u-blox (or Rigado) BMD340 module connected via UART to the compute module....
I have uploaded nordic thingy 91 with lte_ble_gateway program and modified it so that it can connect with 7 devices, however when i try to connect the 6th device I get bluetooth...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
