why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I have the nRF connect application running, but it shows 24 channels, most blue and 3 green. What is the significance of blue vs green? Also, even though I have wifi turned...
I have recently started understanding nRF52840 using SDK v17 and soft device S140 v6.0. I'm using Keil as my dev environment.
Opening any of the SDK example in Keil, when...
Hi,
I am trying to integrate ble based bootloader into my existing system running on nrf52840. I am using SDK 16 v7.0.1 with sd140. To test the process, I have added the...
Hi, I am working on the ble_app_template project. 1-How can I enable simple pairing without NFC? 2-Also how can I set pairing code? 3-Is the write way to secure characteristics...
Hi, I am developing the project where to read the sensor data and send the values to the mobile application as User Interface. I have built the Board with nRF52832 and using...
The size of the FIFO is sufficient. The value is extracted from the FIFO after being received by the UART. Repeat UART reception.
APP_UART_FIFO_ERROR occurs in the above...
Hi everyone,
I'm using SDK 15.0.0 S132v6.0 and looking for a way to get an event when the advertising times out. I discovered the softdevice_ble_evt_handler_set() in this...
Hi,
I am developing a device based on the PCA10059 board, SDK v15.3.0, and softdevice v6.1.1, and I want to imply that I am using the FDS module with 20 pages in my firmware...
Even after I get a license for the Nordic stuff, SES won't show an installed activation:
The license "installs" fine though:
And I do have the "Nordic" version...
Hello,
When I try and use nRF connect Programmer to update the modem firmware via USB it fails each time in the second step (Modem Firmware Update) with the error message...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project, which acts as a central, and an IOS phone as a peripheral. I have a read/write...
I have an nrf52833 wired up to 25 switches and detect changes via the pin SENSE configuration triggering the GPIOTE PORT interrupt. My interrupt handler: 1. reads the pin...
Due to whitelist limitation of 8 peers, I am doing manual filtering of bonded devices. I am trying to use pm_address_resolve function to figure out whether I have previously...
I am using nrf52840 DK and communicate with Raspberry Pi 3 through UART port. The Raspberry Pi is used as a gateway. The baud rate is set at 115200 default on both nrf52840...
Hi, I am trying to integrate ADC in my project( ble_app_template ) but getting garbage data. I have nothing connected with pin P0.4(NRF_SAADC_INPUT_AIN1) . (Means not applied...
