Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I am porting a nFR5340 GCC project to IAR. I can't find any startup files for IAR on the Zephyr stack as there used to be in SoftDevice.Doe anyone know where th eIAR files...
Hi everyone,
I'm working with a nRF52840 dongle. I need to add to the CDC ACM example two bulk endpoint IN. My purpose is to realize a firmware that allow real time data...
I have built several examples in nRF Connect SDK on MacOS and they seem to work OK.
Now trying to build the udp example
I have left the configuration as it was.
I build...
For our user experience, we would like to get rid of the "Bluetooth Paring Request" pop up in iOS.
The device just needs to connect with the iOS device, and should not be...
Hello, I've been tinkering around with the BLE Advertising tutorial on my nRF52840 Dongle (using SoftDevice 140) and I have a question:
How do I configure the dongle's user...
Hi
I have some question about ESB
1. If the noack bit of dynamic payload is set to 0 and transmitted.
Ptx doesn't switch from tx to rx to receive ack?
And prx doesn...
Hello
I use nrf52832 and lithium battery (3.7v, 140 mAh).
I can read the adc value of this battery through the charge IC. I monitored the adc value while charging the...
I find that the nrf52840DK offers two UART function, and when I running the nrf5_SDK/example/peripheral/uart program, there has only one UART configuration example. Can I...
Hello List,
I have a use case where i need to control 2 DC-motors using a PID-controller. The system is to be controlled via BLE, using a nrf52840 with softdevice S140....
Hi all, I am trying to use the nrf52840 dongle with wireshark, I was having permission errors trying to open the device in the program section of the nrf desktop suite running...
Hello,
we think about using an nrf52820 for a multi role solution. I know from the Compatibility Matrix that the S140 is supported and qualified for the nrf52820. What...
hi,
we are trying to add third sensor to the multi sensor example , new sensor is of type binary_input (0x000F) ZB_ZCL_CLUSTER_ID_BINARY_INPUT.
We are unable to subscribe...
I use nRF Connect for desktop / Bluetooth Low Enery Apps + nRF52840-DK.
When run 'start scan', In rare cases, very small RSSI values (-103dbm, -104dbm ...) may be reported...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
