hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I use SEGGER build mesh V4.1 project light_ctl and light_switch.
I flash light_switch_server_nrf52840_xxAA_s140_7.0.1.hex and light_lc_server_nrf52840_xxAA_s140_7.0.1.hex...
Hello Nordic
I am using nrf52832, skd 16.0 , s132 v7, the data with the new FW will be delivered via UART
I wish to understand some issues regarding FW update, after doing...
Hello,
I am working on SDK v14 version mpu6050 sensor. I found an example of mpu6050 here.
https://github.com/Martinsbl/nrf5-mpu-examples
And here I found a way to...
Hi, I am working on nRF52840. I want to add Device Information Service in ble_app_template. (as shown in the attached image its from another device) How can I add? Kindly...
Hello,
nRF52840, SDk16.0, Softdevice 7.0.1,
I am having the following flash write error message while writing data to flash. I'm using FDS library. Interestingly this...
Hi, I am following the below link for creating custom services/characteristics. https://github.com/bjornspockeli/nRF52-Bluetooth-Course
I have set the device name as...
Hi
based on nus example , I'd like to create RX/TX characteristics with a custom UUID (128bits)
My problem is about the UUID characteristics versus UUID service, for example...
I've inherited a project where the software was developed in IAR and I've rebuilt it in SES. I am having an issue configuring the memory for the soft device.
The chip is...
For a project under development I used two NRF24L01 for testing and they work very well.
Now I would like to know if: is it possible to use one NRF24L01 as TX and several...
Hi, I am working on ble_app_template. I am trying to save a value in the flash memory of nRF52840. I am using the following 2 functions to write/read in flash memory but getting...
Hi everyone
I am using app_uart_put() method for sending data via UART. The problem is that when I send each byte I get each byte back to its event handler in APP_UART_DATA_READY...
I have a Thingy:91 connected to a Garmin LIDAR Lite v4 (built on the nRF52840) via four GPIO cables. The code running on the Garmin reads one GPIO pin to signal a measurement...
Hello, I just want to clarify a secondary takeaway from my post:
https://devzone.nordicsemi.com/f/nordic-q-a/60714/best-approach-to-store-nonvolatile-data
I would like...
