I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I am attempting to write a basic I2C program using Zephyr, but I am currently unable to sent a single byte over I2C. Am I doing something wrong? I'd prefer not to use the...
Hello!
I have a characteristic defined to be in user memory by the BLE_GATTS_VLOC_USER flag.
The initial length is 0 and the initial value pointer is NULL.
Now I...
Hello!
I am currently trying to use the watchdog driver from the Zephyr library. I have enabled the CONFIG_WATCHDOG and set it up similarly to the asset_tracker application...
Hi,
so far I have been programming my custom nrf52840 device through the debug out connector of the nRF52840 DK and a custom programming connector.
Now I would like to...
Hi,
I'm using nrf52832 to interface RTC using nrf_calendar.c file.
I have start the RTC at 8:59:00, it will reaches 9:00:00. After that automatically it will resets and...
I haven't been able to locate any NAND flash libraries or examples in SDK 15.3.0
To be clear, this is NAND flash, not NOR flash (examples are Toshiba TC58CYG2S0HRAIG and...
Hello!
We are trying to make a family of devices that would be based on nrf52840. The devices would communicate between each other via Bluetooth Long Range (CODED PHY)....
Hello,
I have a problem using the radio notifications. I use the softdevice V. 15.3.0.
I would like to have an interrupt every time I send an advertisement, which I can...
Dear Nordic,
I am using nRF52832-XXAB, SDK 15
I am aware that in order to enter SYSTEM OFF Mode and woke up by an GPIO event,
I have to set "nrf_gpio_cfg_sense_input...
Hi, I am trying to enable TPS on an application I am staring. I have got it enabled and when I connect to the device using my phone TPS is visable, but I cannot read the value...
Hi all
I have problem with uploading app to this module. On Mqtt_simple I added
CONFIG_BOOTLOADER_MCUBOOT=y
Compile program in Segger and i got app_signed.hex. Im using...
Hello everyone,
I'm trying to make a PWM signal that fires an interrupt at the end of each PWM period. I've had the same question here:
https://devzone.nordicsemi.com...
Hi, All
In our product development, we finally found that our products need to work in long range mode to improve the communication range, and keep the connection with...
Hi,
I am a EE with a lot of background in nRF52 devices. But this is my first software venture with this device. I am familiar with the soft stacks used and have flashed...
Hi!
We develop our product on nRF52840 using S113 softdevice, version 7.0.1. From time to time, we need to erase some part of flash, so we use sd_flash_page_erase() function...
