Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
Hi Noridc guys
recently I got some issues about how to know device network state. then I found there was a issue in zb_bdb_is_factory_new() API.
first, i formed a network...
Hi,
I have a problem of crash device after trying to connect my device to the PC via NFC.
The issue is very rare.
I think that the issue occurs because of an assert...
Hello,
I'm currently testing the bootloader with nrf52832 DK on SDK16.0.0 with Segger Embedded Studio. I followed the guide provided in this link https://devzone.nordicsemi...
Hi,
My project is based on SDK15.3 with NRF52840. I have referred to the "writable_ndef_msg" example to read/write the emulated NFC tag successfully. And I can get back...
Hai ,
In my application i should connect parallel connection and peripheral and central part connections simultaneously.
for this i developed from hrs_relay example .in...
Hello,
I'm trying to program a nRF52840 Dongle with the thread MTD client example by using nRF Connect but I get an error saying I need to add a SoftDevice. I thought...
Hello, I am new to NRF52. I have setup a project under Embitz ide. I can compile GPIO toggle code and program the the code. However when I try an transmit example github.com...
I have 100 samples of string data (Ex: AABBCCDDEEFF:1592636399:1592636399 ) . I am using the flash_fds module. Also, I want to read the read all the samples at once. I am...
Hi,
I am developing the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
However, after I compiled the modified code and loaded to the target broad, I got...
Hi
In ble_stack_init(), err_code = softdevice_enable(&ble_enable_params); err_code = sd_ble_enable(p_ble_enable_params, &app_ram_base); err_code is 4.
I use nrf51822 in...
Hi,
I got a nrf5340 pdk, and I download demo Peripheral_Heart_Rate into board, load peripheral_hr.hex into app_core and load hci_open_amp.hex into net_core. it running ok...
Hello. I have one multirole device (device A) and three peripherals (devices B, C, D). Device A connects to devices B, C, and D as a central role, and connects to the phone...
Hi,
I am developing a product using nRF52833 . (S113, SDK 16, IAR8)
I am developing based on the usbd_ble_uart sample.
I use ble, spi, twi, ppi, saadc.
and, I use...
Hi,
On page 420 of the nRF52811 datasheet (v1.0) it states that pin 14 (P0.18) can be either 1) Digital I/O or 2) Single wire output (SWO). The SWO is not mentioned on any...
