I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello, I'm Jongryul
I want to deliver voice through BLE.
I wonder if this chip supports voice command.
If this chip does not support voice command, I wonder about the...
I'm trying to create a siren tone using the pwm library, that ramps up and down between 2kHz and 3kHz.
Initially I started with the example provided in SDK v15.3.0 nRF5_SDK...
hello community!
Recently I got urgent job to rewrite sensor firmware to nrf52832.
Its not my project basically, another company project.
I wonder why rf52832 didn...
I understand with LTE-M they are supposed to offer greater distances to the cell site, but how do we tell how far away we are from the cell? In the good ol' days, we could...
It says under the S113 information that is supports extended advertising yet I can't see it in the API. I would like to take advantage of the 255 byte advertisement size for...
I want to use NRF9160 for development, now I want to pick something bootloader, so which one do I use
1. \ zephyr, replication, bootloader, McUboot \ zephyr
2. \ zephyr...
I am trying to develop a product with your nRF905. I have two units set up, and can read and write via SPI. However my concern is your poor documentation.
You do not say...
Hello, this is the person who asked about " devzone.nordicsemi.com/.../question-serial-output-uart ". First of all, thank you very much for your sincere reply.
The reason...
Hello
I would like to view the changes in sensor values in real time in a graph. Can you recommend a tool from Nordic or an easy-to-use program?
Thank you.
Sometimes during a DFU update, the NRF52811 can stay in bootloader mode (seen with name DFUTarg and mac_address equal to mac_address +1). I am on Softdevice 16.0 I'm using...
How to read values from 5 Analog pins at the same time
I know how to read from one Analog Pin, but i don't know how to access 5 analog pins at the same time and display...
Hello I am developing a prototype with the Thingy 91 that allows to have the default log in the UART0 <-> USB and collect the data of a sensor through the P6 expansion port...
I have a custom board using NRF52832 which communicates with a BMI160 accelerometer/gyroscope chip by SPI.
I have been developing in Segger Embedded Studio (v5.10d) in debug...
Is the nRF52840 sniffer is support to capture, decrypt and analyze the mesh specific data?
currently, BLE based sniffers can only able to saw a advertise data without any...
I am receiving an unexpected warning from nrf_atfifo_item_get that reports "Get failed - no item in the FIFO." This occurs when I start advertising using
void advertising_start...
