Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Im having errors like Arduino is in the while(1) loop if I enable the DC/DC converter in the characteristics and generate service.h file , If I do not use this setting everything...
I have a NRF24L01 board, which acts as a receiver. It listens on RF channel 2 using address pipe 0 address as follows 0xC47B4D0331. I am able to transmit to this NRF24L01...
I need to wake my uC from sleep when the nrf8001 gets in connected mode and for that I need to supply an external interrupt on hardware interrupts on the MCU.
Will active...
www.dropbox.com/.../error.jpg
it is not even reach main()
same as devzone.nordicsemi.com/.../nrf51422-flashes-ok,-but-debugging-fails-stays-in-moves-r0,r0
is it related...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi
In my project, we wanna transmit large amount of data from UART master to nRF5182, and then to iOS7. Baud rate is 19200. Feed-in speed is near 2KB/sec. BTLE transmission...
I am trying to use this android app to read/write values from my nRF8002. Every few seconds I get a request to bind to the board, even if I already accepeted to bind to it...
I have a example using nRF24LE1.
So. I want know what can I change that example. or how to I get nRF24LU1+ example.
nRF24LE1 example is this.
/* Copyright (c) 2009...
Hi all!
I got a little problem with my ble device.
That is: my device takes system_off mode as initial mode, when being pressed the button, it will wake up and start advertising...
I am using UART0 for wired communication and S110 for Bluetooth LE communication at the same time, using HRM profile. System seems to work as expected, I get log output from...
I am using the nRF51822 to communicate with a HRM (and nothing else), but I intend to use the power of the ARM to control other sensors and process the received data. I use...
Mother board :6310
IAR: IAR Embedded workbench for ARM: 7.10.1.6735
IAR Embedded Workbench common components 7.0.2.3053
Softdevice: S110_nrf51822_6.0.0
sample Project...
