Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi,
I am using nrf52832 to connect 500 nrf52810, among which NRF52832 is central and nrf52810 is peripheral.
How should I do for nrf52832 based on SDK 16.0.0.
Hi,
I want to program my chip nRF51822 ( https://www.waveshare.com/wiki/NRF51822_Eval_Kit ) using the KEIL tool and the ULINK2.
When I try to program the chip KEIL show...
Hi,
I've encountered a problem with opening a project in Segger Studio. I have recently moved to 1.3.0 tag and I am working with Thingy:91 (so I basically open nrf9160 samples...
I'm doing a Nordic example named "Nordic UART Service Client" ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.0.0%2Fble_sdk_app_blinky.html )
The steps...
Hi ,
I ran the example "zephyr\samples\bluetooth\scan_adv" on the nRF9160 dk kit .
It says the following error
"
2020-07-16T02:22:00.682Z DEBUG modem << *****...
Hi, everyone
A LPN ( Node-LP ) had selected one of nodes as its friend ( Node-F0 ), if Node-F0 is taken away, will the Node-LP automatically reselect other node as its...
I read somewhere for new project we should use nrfx driver because in future old nrf_drivers will not be support and improve. All examples in sdk15.3 as I understand used...
Hi All,
I am trying to implement a battery level reading app using NRF52840 DK. It seems I am receiving a timeout from saadc.
In order to run on the Lithium battery, should...
Hi,
I programmed two thingy:91 to return RSRP and RSRQ to a server. On is running with LTE-M and the other with NB-IoT.
I found something that seems strange : +CESQ: 99...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
Opening a project in SEGGER Embedded Studio I have annoying "no entry signs" (white minus sign in a red circle) on the left side various items in a project, whereas most of...
Working with nrf52832_mdk and using basic GPIO functionality, I am unable to toggle the GPIO pins P0.0 or P0.1. The code I am using is quite simple and I am able to toggle...
Hello,
I am working on the mqtt sample from ncs\nrf\samples\nrf9160\mqtt_simple. Mostly the nRF9160 connects to the MQTT server in the first attempt. But sometimes I observe...
