I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello,
I am currently aiming to create an application for the nRF52-DK using the nRF5 SDK and Segger Embedded Studio as my IDE.
Due to the SDK itself being extremely extensive...
Hello ,
I have been trying the Zigbee CLI light example.
And I modifed the main.c file to have the network saved "ZB_FALSE" and then flashed the updated hex file to 52840...
Hi we are having issues with gpiote interrupt. We would like to do some spi read when drdy gpio becomes high to low. I have done above configuration for the same.
We are...
I have a problem collating model publish events arriving at two different nodes in my mesh.
My application is an array of sensors publishing through generic on off and generic...
Hi,
I have a custom board running NUS peripheral which uses the nRF52832 and a NUS central which is running on a nRF52 DK. I modified the ble_app_hrs_freertos example to...
Hi,
I found the communication range using FREERTOS is shorter than which are using non-RTOS.
I know the RADIO TX power and the PHY rate affect the communication range...
Hello,
I am using nrf52832 Dev Kit and am attempting to send information using the ble_app_uart example under SDK version 15 (I don't know the exact rev, but I downloaded...
Hi,
I am using nrf52832 in my custom board and I want to make secure connection between my two boards using stored keys.
Is there any example provide by nordic which I...
I am using the nrf51822 ble with s130_nrf51_2.0.0_softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such...
Hello, basically I want my nRF9160 DK to establish a secure connection with DTLS by using mbedtls .
What I'm trying to do
I'm currently working with the LwM2M sample...
Hello,
My NUS services work fine i can transmit and receive data over UART , but i still get this error in my nRF Toolbox (UART) . Any help will apreciated
Some user datas have been stored in a special page of flash in nRF52832 . However , I need to reprogramme the chip through bootloader , and make sure the user datas not being...
Hi,
I am trying to evaluate the nRF52840 development boards and configure as a simple switch and light node.
The first issue I have had is that on a Huawei phone the nRF...
Hello,
I am trying to find out where to put my persistent storage data in flash.
I have to set start_addr and end_addr, to use fstorage, but I dont know what addresses...
