I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I want to run a mesh application. Can you please tell me the most preferred ide for running mesh examples.
1.segger ide
2.keil ide
Kindly tell me which one is...
Hi,
I'm evaluating the nRF52840 using the DK. I find that the hfxtal in the 52840DK is GSX-223, which is not included in the data sheets characterization of HFXTAL ramp...
Hi, I'm developing a wearable fitness device. The device collects accelerometer-gyro data and sends it to the mobile application. Initial developments are good, I created...
I'm using the <TWI Scanner> example. I use an oscilloscope to measure the signal of SCL (see image)
According to the datasheet, I'm connecting a 4.7K resistor to connect...
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Setup:
Node: 1 nrf52840dk acting as a node flashed with mqtt_client_publisher running on top of OpenThread using the nrfSDK for Thread and Zigbee.
Debugger access via...
How are the pins of the nRF52840 used in the Nina B301 mapped into the Arduino / mbed os system? Using the pin mapping files in the ARduino code often doesn't seem to work...
Background: we have a nRF52832 based design that's been used for the past 1-2 years across a couple 100 piece batches. Our latest batch of 500 boards shows an odd behavior...
Hello all,
I'm using a nrf52840 and it's working fine. However, when I supply the chip with 5v on VDDH the GPIO output voltage is 1.8v. When I supply the chip with 3.3v...
Hi,
We are trying to use an nRF21540 FEM with nRF5340 running the latest nRF Connect SDK. Please can you advise how we can generate the necessary TX_EN/RX_EN signals to...
Hi, devzone
I tested nrfutil6.1.0 dfu ble feature and pca10040 as host board to upgrade another board pca10040, successful!
when test nrf connect desktop v3.6.0 and...
Hi,
I want to use my MPU6050 sensor for my nrf5340pdk board using I2C.
But I face some problems with including the sensor driver.
In my prj.conf file, I do the follwoing...
Dear support,
I am developing a TDMA protocol on a custom board with the NRF52840 and SEGGER EMbedded Studio and the SDK 15.0.0. Everything went well until I wished to reduce...
