hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hello,
I just solved the previous problem thanks to the reply. Thank you a lot.
But, I have one more question..
I was tested UART central example( ble_app_uart_c)...
Hello, I am working on a firmware for nrf52832 custom board, whose purpose is to light an onboard LED if another nrf52832 custom board (same design) is near to it. The other...
Hello,
I am developing a zigbee coordinator with a BMD340 module (using the nRF52840). I want to support several third party device with the coordinator. I am able to connect...
Hi, We have a smart product, which has two application scenarios. One is the use of BLE peripherals, similar to sports bracelets; The other is the 2.4g private protocol mode...
Hi Nordic team
How can I begin to develop the thread mesh? from the https://infocenter.nordicsemi.com/index.jsp I can run which example project
I had no found it from...
Hello .
I want send BLE data of sensor value.
So, I am using the central module(HM-10) And peripheral is nRF52832 of custom module.
Connection and data communication...
Hi
We are working on the FOTA based on http_application_update project. The hardware is Thingy91.
The issue is if we use the default the MCUBootloader on Thingy91(version...
Hi ,
I am working on nrf based project . I m trying to build my project using Cmd . I followed the steps given in link -
https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello,
is it possible to localize the chip via the NB technology.? I red that this is supported by the NB standard.
When I switch on NB supporte systemmode the gps sample...
Are the accepted values of nrf52832 output power as below:
4, 0, -4, -8, -12, -16, -20, -30, -40
What we are most concerned about is whether -30dBm output power was available...
To the kind attention of Nordic support team,
We would like to delete BLE bond infos, only for test purposes. Being BLE not even activated and softdevice not used.
For...
My nRF52840 arrived yesterday and I started playing around with it. It is immediately recognized y nRFConnect v3.5 BLE App v2.4.0. The firmware on the device is 4.1.2 Jul...
Hi There.
I just downloaded a SDK for the wisol module that uses the nRF52832 and i can't get it to compile in Keil V5.31. Im getting this error:
Error: *** Project...
Hi
I am new on nRF52833 and want to try RF test for development.
I have a nRF52833_DK on hand with Direct Test(DTM) in nRF Connect(Descktop). However I am not success...
