hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi, all.
I'm using nRF52832 Software Development Kit, PCA10040, S132.
Using the 'ble_app_uart_c' example, I am studying to connect with my beacons and read data.
I...
Hi,
When evaluated under the following conditions, there was Out of band spurious@325MHz~403MHz (See the following Results ).
Does nRF52832 has spurious(-50dBm~-60dBm...
Hello!
I'm doing the firmware that will be applied to the custom device. This device contains one button, which has two functions. (Function output according to button input...
Hello. I have one multirole device and one peripheral device. Both are nRF53832, SDK version is 15.3 and softdevice is s132 6.1.1. Multirole devices connect to phones as well...
I have two nRF52832 side by side scanning for advertisement with filter by name. Because I will have a number of peripherals advertising, so I want to have multiple centrals...
Hello together,
I want to create a program for the nRF52840 DK and later port it to the nRF52840 Dongle (both from Nordic).
The program should
1) over Serial (USB, that...
Hi there,
I have developed a small sensor device, which generates events when a reedcontact is triggered. When an event occurs a NB-iot message is sent.
However when I...
Hi All,
I'm a student starting a project on a low-power bluetooth accelerometer. I have selected the MC3672 accelerometer ( mcubemems.com/.../) , which will be soldered...
Hello
I am using the ble_thread_dyn_mtd_coap_cli_pca_10056_s140 example and I would like to send 100 bytes of data to display in the logs of the android application "nRF...
hi I am sending a sensor data with time stamp using bluetooth ,now i am sending every data seperately my question is can i store 100such data in structure and send that entire...
Hello,
I have NRF51822 and I need infinite connection. The chip is used as peripheral device. Tx power is set to -8dBm. What is the power consumption when It is connected...
I'm getting a softdevice assertion at PC=0x14CBC after calling fds_record_write(NULL,&record), the record contains the following information:
fds_record_t const record ...
Hi to community!
I have a trouble with nRF52840 when using TWIS. I initialize the peripheral by below code. If the device is reset using default pin 18 by the external...
Hi
I am using NCS desktop application
I ported it to my custom board(52833)，It works well
but now，my custom board has three leds，while nrf52 kbd board only has 1 led...
