hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Dear all,
Pushing the hardware to the limits, I came up with a question about the architecture of the microcontroller itself: Can two different instances of SPIM start...
Hello,
I am experiencing some strange behaviour through DFU process when build with GCC -O2 optimisation.
The upgrade process seems to complete successfully but after...
I got a device with a secure bootloader, but I lost the private key and the firmware got corrupted somehow. Is it possible to flash a new bootloader via BLE or is it bricked...
I am trying to understand the following, hopefully someone can explain:
AFAIK, BLE advertising is stopped as soon as the limit of the SD is reached, AKA the PERIPHERAL_LINK_COUNT...
Hello, I am I'm a novice at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
It's being developed in this environment. Q1 .NRF...
Hi. I am struggling to build the DFU secure bootloader example for the n52 DK development kit. Using SEGGER embedded studio.
I get the following error;
cannot find .....
Hi Support Team,
We bought the nRF52 DK along with the PPK so we can measure current consumption of a DUT. It was working on the power profiler App in nRF Connect and we...
I am starting up with nRF52840, currently i have the dongle but expected to receive my DK in the next few days. This is my first BLE project, so i started reading a lot of...
We have a BLE peripheral implementation using the nRF52832 and both the S332 v2.0.0 and v7.0.1 softdevice. We are supplying the LF clock to the nRF52 from an STM32 MCO output...
Hi,
I would like to set up a couple of boards communicating over Bluetooth; I was hoping someone could provide some pointers.
I would like to connect the nRF9160DK to...
Hello, i'm trying to get usbd_msc example to work on custom, test pcb, with Microchip SST26VF064B flash chip (SDK version 16). As previously advised, i have redefined NRFX_QSPI_PIN_xxx...
Hi,
I wanted to setup a dynamic buffer but I don't have any leads on how to set it up.
Basically, i want to store a stream of data every time it is recorded and then send...
I know this has been asked a couple of times, but I haven't been able to find a straight forward answer.
I have a GPS module that spits out data via UART (no flow control...
Hello, Team.
I always thank to you.
I tried to find some information, but it is a little bit hard to find, so I upload this Q&A.
Now I'm interested in Mesh protocol...
