Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Greetings,
If I send empty line (CR or CRLF) to the modem AT port, modem freezes.
Firmware version: 1.2.1
AT%SHORTSWVER %SHORTSWVER: nrf9160_1.2.1 OK
User application...
Hi,
I have developed succesfully an HTTPs client but I am facing a problem related to a relatively long response from the server when I issue a GET request. After the GET...
Hi,
When I try to update the modem firmware I get this error Errorcode: CouldNotCallFunction (0x9) Lowlever error: Unknown value (ffffff24). See attached picture bellow...
I have a issue with nrf21540 in the Transmit state after the Receive state with using of GPIO for control Transmit / Receive switch.
I'm doing next steps for reproducing...
Hi,
I am trying to use the thingy91 to publish some sensor data to an Azure IoT Hub, I've tried to look at mqtt_simple and modified "asset_tracker" application but I couldn...
Hi Team,
This Query is regarding HF frequency Crystal settings, how to configure the nRF52840 Evaluation board to different frequencies. Actually we need to test the crypto...
Hi there,
I'm attempting to link in a static library archive to my nRF52840 targeted project and receive the following error: Exception table sections and plain sections...
when I use Jlink viewer for tracing, found a fatal error:
1 code:
static void lfclk_config(void) { uint32_t err_code; NRF_LOG_INFO("enter lfclk_config"); err_code = nrf_drv_clock_init...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
hello Nordic
i have s SOM which i want to use nrfutil in it for FDU via UART of an application i have on nrf52832, s132 v7.0.1
i have the bootloader flashed with the...
Up until now I have been the sole firmware developer and the keeper of the keys for our product.
Our scrappy little startup has expanded and is now bringing on additional...
Hi,
Problems I am having with PWM:
1. Using app_PWM and GPIOTE to start and stop the PWM: When button is pressed, GPIOTE handler sets a flag that is polled to start the...
I am using Timer0 and Timer with GPIOTE and PPI to output 2 clocks on 2 pins.
Both timer settings are identical (for troubleshooting). Only timer-0 can be generated at the...
