Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
Hi everyone,
I wanted to make reset pin funtional on nRF52 DK while using pca10040e folder so that I could develop on nRF52810 later, but the reset button did not work as...
I've noticed the idle current of my application changes permanently by ~5uA after using the radio, timer2, and/or the app timer (not sure which). I'm using a custom radio...
Hello,
I am using libUARTE and libUARTE ASYNC for reliable communication over UART.
I need to transmit data that is stored in read only memory but this module seems to...
Hi,
I'm trying to use flash FDS on 10040-Dk with softdevice s132 and freeRTOS.
I debug the code using segger embedded studio, when executing a write to the flash It reaches...
Hello,
we want to support scan for both 1Mbps and Long Range beacons and we are using the S140 6.1.0.
This is the configuration for the scan parameters:
When this...
Hi all,
DFU package V1_0_75 was developed using SDK12 for nrf5232 and V2_0_45 was developed using SDK16 for nrf5232.
I am trying to update from V1_0_75 to V2_0_45 using...
HI
describe my device first:
A Temperature and Humidity Sensor(twi) measure every second
nrf52832 module
it has an lcd and its control IC(twi),
a spi flash to store...
Hi, I want to contribute to your nrfxlib development with the implementation of ZCL compliment typedefs for the thermostat cluster. Can you give me some directions? Below...
Hello
I am using sdk v17.0 and pwm_library example.
I'd like to add a 'dead time' of 10us between the two PWM channels.
Can you give me a good example or method for...
Hi, I've released a driver here.
https://github.com/andrewcharnley/nordic-nrf52-lcd2004-HD447780-i2c-async
Finally NRF52 joins the club supporting the many LCD's out there...
