here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Dear Nordic,
We have almost completed development with nRF52810.
We are trying to improve the accuracy of product operation.
RC oscillator(LFRC) is currently used...
I used the Adafruit Bluefruit NRF52840 LE and added some simple code to this existing timer/counter for pulses: https://devzone.nordicsemi.com/f/nordic-q-a/62633/nrf52-timer...
Hi,
While going through some of the peripheral examples in 'nRF5_SDK_17.0.2', I found it puzzling to see that
the legacy (nrf_drv_*) and nrfx_* drivers are simultaneously...
Hi all,
trying to get CAN-bus support under Zephyr. Have a seed CAN bus shield link connected to PCA10040. The shield use SPI2 connected to MCP2515 CAN controller link ...
Hello
Is it possible to use the qspi of the nrf5340 for custom spi devices? I need the quad spi for the 96MHz speed which the normal spi does not have.
I know of the nrfx...
Hi there,
I am using the Nordic SDK 16.0.0 on an nRF52840 with FreeRTOS. I am quite familiar with using FreeRTOS, but hadn't needed to delete a task until recently. It seems...
Hi everyone,
How could I disable notifications from a characteristic when the peer is get disconnected from the the peripheral? My problem is that when notification are...
Hi,
I was investigating the registers of the nrf9160 using segger embedded studio and found POFCON, which is not mentioned in the documentation.
Can you provide...
I need to add some IPSO objects for our project. It is not quite obvious to me if I need to create modules similar to i e ipso_temp_sensor.c or if it would be enough to use...
Hello, guys!
We are desiging our custom board based on nRF9160 SiP. The board will be battery powered. Li-Ion rechargeable batteries will be used to supply the device. ...
Hi to all,
i am developing a device based NRF52840 soc, and i want to implement a device that need to store some public/private key in somewhere. i know that cryptocell...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
Hi,
I am using app_uart library with Tx and Rx FiFo. I want to check how much space is available in the Tx FiFo at any time, and similarly how much space is filled in the...
Now I am using Nrf52832,SDK15.0.0, S132,
When we developed the DFU OTA function APP, we encountered some abnormal situations: it could not get out in the bootloader mode...
