I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hello, I am trying to develop a rehabilitation exercise service using Thingy52.
Thingy52 is the only device to accomplish my objective which needs motion detection using...
Hi,
I have nrf52840 DK and PCA63511 Power Profiler.
I have two questions:
1. The Average Current Consumption measured with profiler is 110uA (18 mA max, over 10 s...
Hi,
I have Raspberry pi board which i want to use it as a gateway .on which server will get set up.
nrf52840 will be the beacons which i have already set up for sending...
I am trying to use the NRF connect mobile app on android 8.1.0 to try and connect to a Bluetooth server serving GATT request to verify functionality.
The server is running...
Hello,
I am using these pre certified modules https://www.nicerf.com/product_147_88.html in a project which is basically nrf24l01+ with a PA and LNA.
These support ...
Hi,
Just been testing the data rate of write without response commands, I'm only getting about 250 bytes / second which seems incredibly slow?
I've just got a simple little...
Hi,
Is it possible to route an analoge signal through a digital GPIO pin to access the inner analoge pins of a nRF52840? I want to avoid using via-in-pad to keep the cost...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
I have made changes from here in order to configure data rate at Coded PHY for mesh application.
Tested with two phones: Moto G5 Plus (Bluetooth 4.2) OnePlus 6 (Bluetooth...
Hi,
I am tring to display some information using NRF_LOG_HEXDUMP_DEBUG(). However, I can't see anything on the terminal. If I use NRF_LOG_INFO("xxxxx"), I can see the...
I'm using two nRF52840 DKs with SDK 16.0 with one as a central, the other as a peripheral. I'd like to setup an IRK whitelist on the peripheral. I've taken a look at the hid...
Hello,
I'm having trouble getting my program to compile with the SAADC. I started with a BLE template then added the battery service with sensorsim from ble_app_hrs and...
Hi.
I am trying to use nrf52840 on a custom board and configure it as spi slave, and an STM32H7 controller would be the master. I am using the spis example for nrf. I...
