Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
Hi,
Some questions on the scan consumption of nRF52840 and using the attached Online Power Profiler for BLE as reference
If I am using my nRF52840 to scan 24hours at...
I wish to merge the cloud_client example with GPS example. How should I go about it? Along with main.c files of both, which other files will I need to merge?
I am currently making a program that will interpret serial commands from UARTE1 and then send + read something from the other (UARTE0). Previously, when I have been using...
Hello,
I want to be able to send 1 MB of data from a server node to a client node
I have made a simple model with an array that holds 300 bytes.
and upon a timer the...
Hi,
I want to connect Multi peripherals to one central and want to send the device name(peripheral which is connected) through the uart.
How do i get the device name which...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
Hi!
I'm slightly confused with the documentation regarding softdevices S112 and S113. Among other differences, its noted that SD S113 does not support nrf52820 chipset while...
Hi, I have a custom board based on nRF9160 for which I created custom .dts following porting guide. It seems TX isn't sending anything (stay close to 0V) - config I have is...
I
I want to start a sample project on NRF 9160DK and I am facing some issues. I am following the link ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting...
Hi all,
I'm testing the ble_nfc_pairing_reference example from SDK 15.2.0
I have installed microECC and then run succesfully the application using Segger Embedded Studio...
Apologies if this has been asked a bunch of times but none of the posts I ran into were helpful. This is my first time working with a dongle of this nature so apologies if...
Hello,
i am using nRF52832 with Nordic SDK 16.0.0 and s132 7.0.1
in my project i have developed start and stop advertising API and added dis service in project
also...
