This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi,
Greetings!
I am facing a issue while updating firmware
My Setup:
SDK 16.0.0
SDK for Mesh 4.0.0
nRF52832
DFU: secure_bootloader_ble_s132_pca10040
Application...
I've gone through the forum and I've tried certain "solutions" but none of them work for me.
I've erased my device in SES multiple times, recreated the files for the service...
Hi all, I am checking the Uart central and peripheral projects, also the one with usbd and I have one question that may be obvious for you. How do you select the peripheral...
Hello,
I am using nrf52840 and SDK 16.0.0
I am doing some work with the calendar example and got some questions.
Q1.
Inside the main function in main.c file there...
Hi, Is it possible to go from slow advertising to fast advertising with a button press? I did this but it didn't work:
P.S. I slightly modified names and operation of my...
Dear,
We just start to development our project. I use the Segger + nrf5_SDK_for_Mesh_v4.0.0.
I open the light switch sample project from "nrf5_SDK_for_Mesh_v4.0.0" by...
HI,
I am working on the interface between the nrf52832 and the MPU9250 IMU.
I have communication working fine with using nrfx_twi, but I have the following error when...
Hi,
I'm writting a simple test code that uses the aplication timer library (app_timer) to wake up from SystemON Idle mode to SystemOn mode every 1 minute. The idea is to...
Hi All,
I wan't to have logging via segger RTT from enabled modules in the MESH SDK.
Tried several config options in sdk_config.h, but without luck.
I made a diff of...
I'm using the app_timer library to create one shot timer. I'm calling the app_timer_start() to the same timer repeatedly in the gpiote handler. I had thought that this would...
Hi ... i want central to connect to the two different peripheral mac address , i am using ble_app_uart_c example version 15.2 .. using scan_filter_address i can abe to connect...
We are using the soft device (s140) in SDK version 16, our device is configured as a peripheral.
I have a program that connects to and then immediately disconnects from...
To the kind attention of Nordic support team,
using these commands, like in https://devzone.nordicsemi.com/f/nordic-q-a/58365/doing-dfu-ble-as-a-pca10059-dongle ,
I flashed...
To the kind attention of Nordic support team,
I'm using a command like this: nrfutil dfu usb-serial -pkg x.zip -p COMx.
I use it to program a default PCA10056 DK board...
I have system on sleep mode implemented which is still drawing 8mA of current i would like to take it down to 1mA or less what i need to do to get it that low?
I have two...
