Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
I am using the ble_app_uart as the basis for my project, where the NUS is used to send and receive data from my mobile app. The outgoing data is generated internally...
Hi, I am trying to run the periodic_adv sample on nrf9160dk_52840 which was added to the samples directory of the zepyhr repo 15 days ago. I am using nRF Connect SDK v1.4...
Hi Sir,
We have the " Capacitive sensor low-level library " as below in Nordic SDK.
1. err_code = nrf_drv_csense_init (&csense_config, csense_handler);
2. nrf_drv_csense_channels_enable...
Hi,
I use nRF52840 DK with SoftDevice 140 v.7.0.1 and SDK 16.0.0.
I want to get RSSI information (along with channel index) for BLE extended advertisements.
I enabled...
I am working with a custom hardware device similar to the Thingy91. I am communicating with an external device using COM1 using a binary stream at 38400 N81. (COM0 is assigned...
My design uses an RV-3028 RTC as an external 32 kHz oscillator for the application timer. Do I have to configure the SDK to use an external oscillator instead of a crystal...
I recently updated my multi-protocol (Thread FTD + BLE Peripheral Connectable) to use 'nRF5_SDK_for_Thread_and_Zigbee_3.0.0_d310e71'. I had been previously using 'nRF5_SDK_for_Thread_and_Zigbee_2...
Hi,
I setted up the LIBUARTE on my custom board...
NRF52833,SDK17.0.2,With Softdevice enabled
CODE:
-----------------------------------
NRF_LIBUARTE_ASYNC_DEFINE...
Hi,
I've found an issue while writing data to QSPI flash memory on the nrf52840 DK board with sample application.
The issue is that the data is overwritten to 0x0 address...
I am working on putting my NRF52840 to sleep with the RTC running (System ON WFE, not System Off). According to the datasheet, I should be able to call a soft reset and keep...
Hello, I am having some problems with what i assume is the readback protection. Is it possible to update the firmware of the device without deleting UIRC (serial number among...
I am using nrf52 chipset, I just want to know did anyone tried to run docker container to create ARM image? I am thinking to use Docker container as CI.
Hello
I am using nrf52832 and ble_app_uart of SDK v17.0.
I am sending data to the app every second through the notify function. If I try to disconnect and reconnect Bluetooth...
Hello,
Is the Power Profiler Kit II (PPK2) only usable for nRF product line and custom boards, or can it be use beyond the nRF line of products such as boards not made by...
Hello!
I am currently working on a project with my nRF52832 that is using BLE communication with a android phone. I have tried some of Nordics' examples that use BLE, but...
