Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi all
I'm using nrf52805 soc, softdevice s112 , sdk version 17.0.2 and nrf connect mobile app for my project development. I can connect and disconnect the nrf52 device...
Hi,
I am using P0.10 GPIO of nRF52840 (QFN package) as an output for driving a transmission circuit with an 8MHz digital signal.
According to the datasheet this pin is...
Hi team, I'm using Mesh in my project. Using this thread as a reference, I tried to decrease the data throughput and experiment to see if devices could communicate with each...
hello,
i want to know if is possible have Multilink, ble Uart and relay together? it is for make an a type of Mesh network of 4 devices with a BW of 1Mbps (see the image...
Hi
I'm testing the SLM application in nRF Connect SDK ver 1.3.1 on nRF9160 PDK ver 0.8.2 using the LTE Link Monitor v3.5.0
Giving the following commands, the UART stop...
hello ,
i am working on recieving data from sensor using nrf52832 with time and data right now i am getting time that is set by me my problem is i have to set time automatically...
Here is an issue I am having when using MQTT in a poor (RSRP < 15) LTE signal environment
Condition:
nRF Connect SDK v1.3
modem firmware v1.2
TLS Socket is configured...
I've worked through the Custom BLE Service example ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) and I'm attempting to port it to C++ to form the...
Hi,
I need to write a linker (ld) script for our nRF52 application. Essentially I need to combine the linker script that we already use with the scripts that exist in the...
trying to build a long range coded phy broadcast/scanning application. as I know zephyr doesn't support that so we have to include nordic link layer based on this post
https...
Hello all,
i am using ble_app_uart example.I add the line
in the begining of the main function. All the ble connection works, but putty shows strange characters...
I am having a bit of trouble getting high enough data throughput for my application so I have a few questions regarding it.
Can running the spi/other peripherals affect...
Hi，
I tried to build a BLE sniffer environment. And it works well to capture the LE secure connection air packet after Eable Secure Connections debug mode （uses the debug...
Hi,
using:
SDK for thread and Zigbee 4.1.0
NRF52840dk
I am trying to add UART (for my custom application) to an existing Thread example with CLI. (e.g. ble_thread_dyn_hrs_coap_srv_freertos...
