Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Running nRF Connect SDK v2.1 targetting an nRF52840 DK (PCA10056)
I'm looking at the OTA DFU options for this SDK. The host side tool if i'm not mistaken is a go utility...
Hello,
I'm trying to integrate Mesh 4.0.0 into a program built with SDK 16.0.0 but I'm running into some issues including the correct files from the Mesh SDK. I followed...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
We are using a BLE module EYSHSNZWZ from Tayio Yuden which contains the nRF52832.
using SDK 15.0.0_a53641a and Softdevice and Softdevice s132_nrf52_6.1.0
The application...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I need to use a custom board with old nRF51822 rev.2 (QFAAG0). The compatibility matrix indicates S110 Softdevice SD5.2.1. I found only 7.3.0 or 8.0.0 and there is no...
hello
i need a device capable to work with Bluetooth 5.2 to transmit audio
is nrf52840, nrf52820, nrf52832 or any other support Bluetooth 5.2 and has Protocol stack...
Hi community !
i put the same question here but with less explaination : https://devzone.nordicsemi.com/f/nordic-q-a/61393/mesh-uart-coexistence-communication-with-pc I...
I am evaluating if I should change to nRF Connect SDK for a new project so I have been updating nRF Connect to latest version v3.3.3
I have installed Getting Started Assistant...
Hello, We are developing a application that sends some data to AWS in some intervals(3 - 15 minutes). This application were currently being tested on custom nrf9160 boards...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
Now I am trying to do the same for generating SoftDevice...
