Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
i use the demo ble_app_uart ，and i want to close the uart when ble is "Disconnected"。
but it when it do app_uart_close(),the nrf52810 is RST。 i use the same code in nrf51822...
In the nRF52840 do the peripheral interrupts (e.g. UART ENDRX) set the event register in the ARM core? If so is __SEV(); __WFE(); the only way to clear this event?
Project Starting Point I have a Zigbee end device that until recently, did not include an MBR, Bootloader, or the OTA cluster. Prior to the implementation of the previously...
Apologies in case query is dumb or not conveyed properly or duplicate query( related topic responses did not resolve/clear up topic for me)
What are the changes required...
Hi,
I am using Nordic version of SES v4.42, I am not able to debug and conformed that this version is having an issue details given in link below
https://devzone.nordicsemi...
Hello, I am using nordic nRF51822 chip and mbed api. I am creating a custom GATT service .
In the service , I tried to make a characteristic on BROADCAST mode rather than...
Hello,
I am making a low-power beacon.
I am using NRf52832 module with external crystal. No extra device.
I use SDK 14.2.0, because it's much easier than 15.3 for making...
Hi,
Got some questions about receiving adv packet in Mesh Beaconing Example:
According to the description " The beaconing example also demonstrates the usage of the Packet...
Hi,
Good day! I hope everyone is doing well.
I have a weird problem measuring Li-ion battery pack voltage.
Problem: Tried to measure battery pack voltage 12.6V using...
We're struggling a bit with our NFC implementation. We were using the T2T library, using the examples, and it was working fine. However, we saw current drain at ~ 400uA, which...
Currently I am testing the coap_client and https_client sample application with nrf9160 based custom board. But the board is continously resetting while searching for the...
Hi there,
I was wondering how the motion pane is supposed to work in the bifravst app, it doesn't seem to be refreshing. The battery pane doesn't seem to be refreshing either...
Hello.
I'm reading the documentation of the radio peripheral of nRF52832 but I can't find any information about the S0 and S1 fields.
What are those fields? What do they...
Hi, guys. I'm using the PCA10056 and the SDK 15.3's BLE UART peripheral example. I'm working on a PWM controller using the mobile app.
I need to create a delayed PWM signal...
My current project is to build a simple BLE LED controller. The goals of this project are to familiarize myself with lower level modules and to practice designing/building...
