Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
I have noticed ever since I updated my nRF9160 DK modem firmware to the latest version v1.2.0 frequent registration dropouts and very sluggish MQTT performance.
My...
Hi, I recently bought a Nordic Thingy 52 and it looks great ! It looks like there is a decent mic and speaker on the device and I was intrigued if the device could act as...
Hello,
I am trying to do communication with external module using UART0. But when I connect pin P0.28 (RX of UART0) to external module to receive the data, there is no data...
Hello,
I am working with SPI on the Nordic nrf9160. I am currently on the DK.
The board I need to interface through SPI works at 25MHz (minimal frequency) and I would...
Hi everyone,
I know that I can configure the resolution of app_timer by adjusting the prescaler form sdk_config.h
However, what is the practical purpose of prescaler...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf52840dk board. After generating hex file, I upload the...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf51dk board. After generating hex file, I upload the program...
Hi, I want to write 510 bytes of data to my BLE Characteristics, so I set parameters ble_gatts_attr_t max_len as 510 and its variable length attribute. Also I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello,
I just bought a new nRF5340 PDK and wanted to learn it a little bit. I searched on the internet and found very useful information about nRF53 architecture.
But...
Hi,
We have a question regarding a custom implementation of flow control for nrf52840 using SDK16 w/ SoftDevice 7.0.1. Currently, our sensor's primary micro transfers data...
A newbie here. I am studying the simple_timer application in the nRF5_SDK_17.0.0_9d13099 library.
The sample application sets the clock frequency to the timer at 16MHz....
Looking around to develop hardware/software using the RAK4600 module!
RAK4600 (lora Node) uses Lora as its main way to communicate with my Lora server (normal flow).
Consider...
Hello,
I would like to switch on a led of a nrf52840 dongle by pressing the buton of another dongle. I don't know which example to use from SDK 17.0.2 to make a master/slave...
Pairing is rejected after setting,
i)APP_ADV_DURATION to 0
ii)adv. flag in adv. init from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hi,
I tried to implement the UART in my code, based on the UART example code. Just as in the example, I first define the struct with the pin numbers:
The pins in this...
