Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
i have a question relative to the configuration tool File Format.
I'd like to modify (automatically) the configuration file in order to change the "Device Name"...
I am using a Bluetooth NRF 8001 module. I want to send data to the module from my android phone to the bluetooth module connected to an Arduino. For sample test I used nrf...
Dear Håkon Alseth,
you posted twi source code which took care of all SD/PPI stuff here and it was also linked here , but it is no longer available. The whole forum seams...
Hello,
I use the bootloader in SDK v5.2.0 and could not run APP after DFU completed.
It always stay in the DFU state.
After checking the memory by J-Link commander, something...
At work we are primarily interested in using the 128kb nRF51822 devices. I am able to get a softdevice and bootloader onto a 256kb device just fine. When I attempt to do the...
Hello all,
I want to send some sensor data( collected by Pic controller) to other BLE client(may be a phone) using nrf51822 via UART. Can somebody suggest how to communicate...
Hi,
In the reference design of "nRF51822-QFAA_ST_BAL-NRF01D3", the datasheet recommends this crystal ( www.digikey.com/.../3125558) , but we are out of stock from local...
Hello all,
I have flased "ble_app_hts" example for nrf51822 on evaluation board PCA10001. In the application both the LED pins are configured for output using "nrf_gpio_cfg_output...
I have a large array of uint16_t data to use as a lookup table, which is defined in flash. It's 4002 bytes in size, and I can set where in flash it is saved. I'm accessing...
I am using an nRF51422 and attempting to interface
it with an MPU9150/6050 using your MPU6050 driver and
the underlying twi_hw_master.c.
I have modified twi_master_config...
Hi all,
My application gathers sensor data and uses the advertisement packet to broadcast the values (much the same as the nordic temp sensor example). Rather than having...
Dear developers,
I need to turn nrf8002 to master mode in order to use Alert Notifications of "Profiles - On Master" offered by nrfgoStudio. I need these profiles to activate...
I'm trying to send data acquired from the ADC and monitor it using the master emulator.
The values I'm getting do not appear to make sense though.
I'm using the BLE_HRS...
Hi,
Original UART DFU bootloader SDK example ported from NRF6310 board to PCA10001 board does not work.
What did I do wrong - can anybody please help me ? Thanks in...
