Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Dear Nordic Tech Support & community,
The SDK 16.0.0 supports only one button long-push at time. Attached you can find a SDK-patch to add the support of multiple long-press...
Hi Team
I am trying to implement the firmware upgrade for master controller nrf52832 on chip using esp8266 over uart and I am very new with this boot-loader part.
I...
Hi
I had implemented a DFU module in esp8266 where I am trying to upgrade nrf over serial (UART Communication).
I had success with Init file write but when I send the...
Hi,
I am using nrf52833 EVB as an SPI master. The data is sent properly and well-received at the slave, however, I have a problem with the data received.
The problem...
Behaviour:
- Bluefruit the feater (nRF82832)
- Bluetooth BLE
- Implementation of Fitness Machine Service (0x1826)
- What is correct : all characteristics notified...
Hello, Nordic!
Our project is at evaluation stage. We aimed to build an Bluetooth 5.1 AoA indoor locator system, where the reciever should know the location of the transmitter...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
Hello,
I have several nrf52 Development Kits which will be used for creating a Bluetooth mesh network. They sport the NRF52832 SoC.
Do they have, or will ever have, support...
Hello
*Environment
- LG V30 (Android 9)
- nRF52832, 15.3.0 SDK, S132
- nRF5340 ( I can't find SDK version)
I have some issue.
LG V30 Mobile can't reconnect...
Hi,
I am using nRF52840 USB dongle and DFU trigger library to update firmware without push any button.
The Python 2.7.x is working fine for DFU trigger into the DFU mode...
Hi!
I am developing a iot solution and I wanna send sensors data to broker by MQTT publisher. In my code already has the W5100 development and now I want to connect my device...
Hello,
I would like to create a new box in the nRF cloud for recording additional data. I know these boxes allow exporting the recorded data into a CSV file, which is ultimately...
Hi,
I have the below queries regarding the power consumption and memory
1) If my device is connected to the mobile phone and if it is scanning and the same it is advertising...
