When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi.
I am a student studying esb examples with nrf52433 board.
1. If data is sent from ptx to prx using static payload, is tx completed without receiving ACK? Don't need...
Hello,
I try to measure the current of the nRF SoC on my NRF52-DK, by using an oscilloscope and USB as a power supply, related to the guide from Nordic from here:
https...
Hi,
I need to write a 32-bit value to an NVM flash page whenever my code hits an assert failure. This failure can occur anywhere in the code - my application, the Nordic...
Hello,
I'm working on a circuit which has a pin connected to a pull-up resistor, using the nRF52 DK and SEGGER Embedded Studio 5.20 to develop the software.
This pin is...
Hello everybody, I am using Zephyr with the nrf52840-dk device. I would like to store the DTLS credentials with a secure way. I don't want to be part of the code and thus...
I have been testing out HTTPS with the http_application_update .
I have been able to successfully setup a TLS 1.2 connection, but I was seeing a lot of "Peer closed connection...
Hello
I would like to modify my Transmission Parameters of my Thread network. According to the CoAP protocol ( https://tools.ietf.org/html/rfc7252#section-4.8 ), it is possible...
Hi Dev Team,
I am trying to measure the low power performance of the nrf9160.
For this, I tried to use the "system_off" example in the folder : C:\Users\adeel\ncs\v1.4...
Hi,
I'm trying to alternate between the beacon sample and the central sample in one application. It builds and initiates, the connection example from central is functioning...
Hello everyone, this is my first time participating in the forum. I am a very new hardware and firmware developer (this is my first job in the industry of iot). I have chosen...
We are currently evaluating external memory on the NRF52840 and are trying to use external memory within the memory space of the processor (XIP). We are aware of the erratas...
Hi, I am using nrf52840 as a peripheral. How can I use more than 1 uart(1 for GSM,2nd For GPS, and 3rd for show data in PuTTY). Which pins I can use for this? and how? any...
Hi,
We have a requirement where we need to store some application parameters (Eg. APN name ) in the nrf9160 flash. This parameters will be storing during production time...
Hi,
1. I was trying to measure the Bluetooth throughput of nRF5340PDK using the sample from ...\ncs\v1.4.0\nrf\samples\bluetooth\throughput, but from what I see in the requirements...
