Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi,
I would like to clarify a few points related to the power saving modes of the nRF9160 and how it behaves in low-power states.
1. PSM Current Consumption — What Does...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
I am using zephyr_nanopb_sources to add some protobuf files to my app target, and this works fine in a normal build without mcuboot. However, when building with mcuboot it...
Hi,
I need to use the GPIOTE with interrupt function with nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board.
So I created a build...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
I have problem with i2c that can't read the cst816s, its always return log message `<err> cst816s: failed reading chip id` and `<err> cst816s: Could not read x data` when...
Hello Nordic Team, I recently encountered an issue similar to the one discussed in the post .After testing multiple device types, I found that only generic switche is recognized...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
Hi,
We are currently CE certifying our product, and the test lab requires a fixed frequency firmware for the device. Are there any generic samples for this within nRF Connect...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
There is a possible typo in the nRF5340 DK documentation.
https://docs.nordicsemi.com/bundle/ug_nrf5340_dk/page/UG/dk/ext_programming_support_P20.html
In the top picture...
Testing with NCS 3.0.1 and nRF54L15-DK. I would like my devices to be able to work as channel sounding initiator as well as reflector role. In my own code I have integrated...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
