Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
Hello,
I got the acceleration value using mpu6050 sensor. And I am going to use this to get the angle of the sensor. The formula below has shown that angles can be obtained...
The application cannot write the app_update.bin on Windows.
How do I write with MCUboot & DFU & application?
[Command I tried]
dfu-util --alt 1 --download .\build_nrf52840dk_nrf52840...
Hi,
I have a similar issue as Wille in his question . I was trying to alter the example "nfc_text_record" for my needs. The code compiles without a problem, but when I try...
Hi,
After setting up my IDE and toolchain and trying out some example codes, I wanted to try the example for NFC pairing from SDK ver 17.0.2, because the pairing via NFC...
Hello,
I have some questions relate to Advertising:and RF ANT:
As I understand about advertising, there are only 3 channels, which can broadcast the advertising, are...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to follow this example.
I connected successfully, but I have problem in 'Advertising' part...
Hello, Support team:)
I wish to use NRF_LOG_DEBUG function in segger embedded studio.
But there is no message in "Debug Terminal".
- nRF SDK 16, "/examples/proprietary_rf...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
UART works normally at 3.3V.
But if I lower the power...
Greetings. I am on a mission to upgrade the BLE Firmware of nRF52840 via UART and ultimately via the UART communication between our main Micro (Microchip PIC) and nrf52840...
Hi,
I am developing a product using nRF52832 . (S132, SDK 17, IAR8)
I am developing based on the ble_app_uart example.
I would like to add a basic PWM code to...
