Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I search a NORDIC example (RF52832) that is bonded with a battery CR2032 as power supply runs very long (> 1 year).
Bonded with whitelist
Bonded with one or...
Hello,
I want to create/compile a (Nordic) secure bootloader with serial output.
I know the example of the dfu secure_bootloader. I also know there is a nomal and a debug...
I am using NRF Connect SDK on NRF52840 Dongle and I have written two programs. First acts as bluetooth peripherial device, second acts as bluetooth centeral devices. I have...
Hello! So I'm working on a project where I try to connect the nRF9160 DK to the google cloud. I tried to manage this by following this guide: https://devzone.nordicsemi.com...
Hi,
I'm using the BLE app (ver 3.6.0) in nRF Connect for Desktop together with a PCA10056.
I'm scanning for a device that sends three ADV_EXT_IND, one on each channel...
Hi,
I am using the USB CDC example in my project, where I developed my own application level communication protocol.
I have a problem with the data throughput, it's...
I am designing a custom board with a nRF52840 module that has no 32.768 kHz crystal embedded in it and as a first step want to test it with some examples that use only RC...
Hi all,
I'm trying to setup an interrupt-driven UART. UART is able to transmit data, but I don't get the TXRDY interrupt.
Below is my minimal initialisation that outputs...
I developed on sdk16.0 and found that app_button has abnormal power consumption,
so I replaced it with app_button of sdk15.3, but found that no key events were reported...
I want to use UARTE to handle terminal style messages. That is, messages are ended with a newline, I have absolutely no idea how long they will be, and the delay between multiple...
Hi there, Just wondering how to get the comparator "RESULT" (not part of EVENT) onto an output pin without CPU intervention. From the datasheet I believe: 1. the RESULT is...
I am a newbie with nordic, where I have recently purchased the nrf52810 device. I need some guidelines to get started. My intention is to read data via TWI from an MPU6050...
Hi,
In past we have observed BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION as a disconnection reason when the application layer tries to disconnect because of a timeout. But...
Hello, we are developing a project solution where we want to pass data between multiple sensor devices using BLE advertising data. For now, we have a test setup with two nrf52832dk...
Hi,
I would like to catch in main.c the nobody connect after advertising event via ADV_SET_TERMINATED.
I can see with breakpoint program jump into ble_advertising_on_ble_evt...
